Control the Elements Owner’s Manual – 3200VSi / 3200VSx / 4200VSi / 4200VSx
10 II. Installation Instructions TEST THE UNIT BEFORE INSTALLING IT 1. Remove the unit from the box. SAVE THE BOX AND PACKING MATERIALS. 2.
11 Mount the unit in the upright position close to the ceiling inside the cellar. As warm air rises to the top of the cellar, the cooling un
12 3200VSi / 4200VSi – Mounting Diagrams
13 3200VSx / 4200VSx – Mounting Diagrams
14 Installation Notes: 1. The unit is shipped with (4) wall mounting brackets, a 90° drain elbow, and a 10’ length of ½ ” I.D. condensate d
15 As shown above, the drain line should drop, then rise (but stay below the height of the fitting), and then drop again into a drain or buck
16 Ducted Installations – Rear Duct Kit 1. Ductwork may be attached to the discharge only, or to both the discharge and return adapters. 2.
17 Ducted Installations – Front Duct Kit 1. Remove the front grill (if present) from the front of cooling unit before attaching the front duc
18 Front Duct Kit - Cut Sheet Summary Keep in mind the following guidelines before purchasing a wine cooling unit from CellarPro: If the
19 III. Operating Instructions Overview Test the cooling unit to make sure it is working properly before installing the cooling unit (refer t
C O N G R A T U L A T I O N S ! Thank you for purchasing a new CellarPro cooling system. Please take a minute to read through this Owner’s Manual
20 Basic Operation The temperature inside the cellar can be increased or decreased by changing the Minimum Set Point as described later in th
21 (1) Control Panel: Maintains desired cellar environment. Factory settings are optimized for peak performance. Controller is described in de
22 Control Panel Instructions Digital Display The temperature displayed on the control indicates the real-time air temperature as meas
23 Up and Down Buttons To view the “High Temp” recorded by the cooling unit, press the “Up” button once. To view the “Low Temp” recorded by
24 Energy Saver Button To activate and deactivate the “Energy Saver” mode, press the “Energy Saver” button. The “Energy Saver” indicator l
25 Remote Control / Display Instructions Digital Display The temperature displayed on the control is red instead of blue. Quick Chill B
26 HUMIDITY: The factory preset for this setting is “3”. If the humidity inside the cellar is too low, press the “Set” button, then use the “U
27 Standard Protection Mechanisms The cooling unit is programmed to shut down certain components to protect those components, as well as the win
28 Maintenance The condenser coils at the back of the cooling unit will collect dust, dirt and lint over time. It is critically important to clea
29 The cooling unit has both an audible notification and a visual alarm indicator (shown in “red” on the control panel) that are activated when a
3 Table of Contents I. Specifications 4 II. Installation Instructions 10 III. Operating Instructions 19 IV. Troubleshooting 30 V. Limited W
30 IV. Troubleshooting Cooling Unit Runs Constantly Improper installation, inadequate insulation, or a cellar that is too large will cause th
31 4. Raise the Minimum Set Point of the cooling unit. 5. Check to make sure the cellar has airtight seals, including the door(s), light fixtur
32 VI. Limited Warranty For five years from the date of original delivery, your CellarPro warranty covers the internal compressor if it proves t
4 I. Specifications Specs and Cut Sheets Model Dimensions (inches) W x D x H WeightRunning Compressor Amps 3200/4200VSi 14.1 x 25.1 x 19.6 (
5 3200VSi / 4200VSi (with Rear Duct Hood) - Cut Sheet 3200VSx / 4200VSx Cut Sheet
6 Placement CellarPro 3200 and 4200 Series cooling units are designed to be installed THROUGH THE WALL, so that the rear and the front of the
7 have a minimum of R-19 insulation and a vapor barrier on the warm side of the insulation. Doors also should be insulated and tightly sealed wi
8 the heat will not dissipate. In this event, the cooling unit will be forced to re-circulate its hot air exhaust and/or the static pressure wil
9 Power Requirements CellarPro cooling systems should be plugged into a dedicated non-GFI outlet connected to a 15-amp circuit. The cooling un
Comments to this Manuals